ForDiag.cz http://forum.fordiag.cz/ |
|
Escort 2.0 16v Cosworth 2pin konektor http://forum.fordiag.cz/viewtopic.php?t=157 |
Stránka 1 z 2 |
Autor: | Tomin [ 19 srp 2013, 21:01 ] | ||
Předmět příspěvku: | Escort 2.0 16v Cosworth 2pin konektor | ||
|
Autor: | jsa [ 26 srp 2013, 22:36 ] |
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor |
The connector bundle is normally clipped to the bulkhead, down behind the strut tower on the left side of the car. At least for the RHD cars. |
Autor: | Tomin [ 27 srp 2013, 09:47 ] |
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth EEC IV 2pin konektor |
Perfect doc. Thank you. |
Autor: | jsa [ 29 srp 2013, 12:13 ] | ||
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor | ||
R1 of the pdf contained an error, so if you downloaded it, please delete it and use this one.
|
Autor: | midnight_man [ 21 úno 2018, 19:55 ] |
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor |
zdravim, potrebujem riesit diag na EEC-IV pre cosworth 2.0 jednotku... zvlada to ford diag? je nutny priamo kabel od ford diag? alebo stačí USB kkl? elm? ktorý konektor sa pouziva? cosworth ma 3 pin a 2pin diag konektor..oba idú do roznych pinov na ECU... dakujem |
Autor: | Tomin [ 21 úno 2018, 20:07 ] |
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor |
ELM ani KKL to nezvlada. EEC IV pouziva specialni protokol Fordu DCL. Fordiag to umi. Pripojuje se na 2pinovy konektor. Viz. http://www.fordfans.cz/phpbb3/viewtopic ... 46#p305446 http://www.fordfans.cz/phpbb3/viewtopic ... 14#p313514 http://www.fordiag.cz/pics/img_3558.jpg |
Autor: | midnight_man [ 22 úno 2018, 22:21 ] |
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor |
ahoj, dakujem ...v tom pripade je to zaujimave a zistujeme ze EEC IV pouziva 2 protokoly!!!!! pretoze na tom 3 pinovom konektore máte vlastne Kline, Lline + GND. ked zapojite Kline,Lline, GND a 12V do obd konektora z toho 3 pinu, bez problemov precitate EEC-IV autocom, delphi alebo iným diag pristrojom ktorý pozna sierru, fiesta a pod...(vcera testovane) Ten 2 pin konektor ide na ine 2 piny a zrejme pouziva specialny ford protokol...no sranda!!!! |
Autor: | jsa [ 23 úno 2018, 00:10 ] |
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor |
Citace: hello, thank you ... in this case it is interesting and we find out from EEC IV uses 2 protocols !!!!!
The car has 2 protocols in place. Kline related hardware may be inside the eec but it does not access engine control code.Citace: The 2 pin connector is on 2 pins and apparently uses a special ford protocol
download/file.php?id=73google CHAPTER 13 LHBH0 DCL and you should find some ford literature on it. DCL uses RS-485 drivers, so two wire around 3V differential. |
Autor: | midnight_man [ 23 úno 2018, 00:16 ] | ||
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor | ||
1300 pages of reading....but sure 2 protocols..
|
Autor: | jsa [ 23 úno 2018, 00:37 ] |
Předmět příspěvku: | Re: Escort 2.0 16v Cosworth 2pin konektor |
Chapter 13 for DCL. In others Ford also have SCP and of course OBD eventually. |
Stránka 1 z 2 | Všechny časy jsou v UTC+01:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |